Help the development of the site, sharing the article with friends!
Sand in the pool is not pleasant. The sediment clouds the water and is clearly noticeable. There are various tools that you can use to effectively remove the sand.
In a nutshell
- Skimmer against drifting sand
- Remove sand from the bottom with a pool vacuum
- Water exchange with large amounts of sand
use skimmers
The skimmer is the easiest solution to remove sand from your pool. The tool is particularly useful in the long term, as it is not removed after installation. Once installed, it permanently filters the water surface, removing light sand at the top of the pool. Skimmers are not suitable for cleaning when the sand has already sunk to the bottom. You don't have to worry about sediment removal yourself. Nevertheless, you should pay attention to certain points so that the skimmer works optimally over a long period of time:
- Empty the tank regularly
- run while bathing
- Do not place chlorine tablets in skimmer
- reduces effectiveness
- Sand is only poorly filtered
An installed skimmer in the pool helps filter out sand from the upper layers of the water.
vacuum sand
Not only a skimmer helps to remove sand in the pool. The use of a pool vacuum is particularly effective when the sand is at the bottom of the pool. A skimmer is not sufficient in this case, as it can only clean the top layer of water. The sand would have to be constantly lifted off the bottom for the skimmer to remove that sand. This is hardly possible, especially with heavy sand. For this reason, you should rely on a pool vacuum. The application is more time-consuming depending on the amount of sand, but the result is immediately visible thanks to the tool. In addition, only the pool vacuum is required for this method. The following guide will help you:
- Set the filter system to backwash
- Turn on the pool vacuum
- Vacuum sand from the floor
- can also remove sand from upper layers
- Thoroughly remove sand
- Turn off the pool vacuum
- then fill up the pool with fresh water
- optional: treat water
Tip: Use a pool brush to sweep the sand into a corner before vacuuming. For pools with vinyl walls, use a soft bristle brush to avoid scratching the walls and floor.
water exchange
One of the simplest, but at the same time time-consuming and costly methods of removing sand from the pool is complete water replacement. This is particularly useful when there is a lot of sand that has gotten into the bathing water. There can be various reasons for this:
- sudden sand drifts
- spilled sand (e.g. during transport)
- many bathers
As soon as the sand is clearly visible in the bathing water and the use of a skimmer or pool vacuum is not sufficient, you should make use of the water change. To do this, follow these instructions so that there is no sand left in the pool at the end:
- Adjust the backwash on the filter
- drain water
- top up with fresh water at the same time
- let it run until the water runs clear
- check regularly
- Set filter normally
- treat water if necessary
- disinfect to finish
Tip: If the drained pool water does not exceed a chlorine value of 0.3 milligrams per liter, you can use it for watering. The sand in the water does not even have to be removed for watering.
frequently asked Questions
How can sand drift into the pool be prevented?Wind can get sand into the water. To prevent this problem, you should use a pool cover. This prevents sand from getting into the water when the pool is not in use. It is simply stretched over the pool and removed before bathing. It is best to swim on calm days to avoid sand being blown into the pool.
Do bathers get sand into the water?Yes, if there is sand on the body, it will be carried into the water. For this reason, it is recommended to remove the excess sand on the body before bathing. Pool showers are ideal for this purpose. The short shower reliably removes the sand. If there is only sand on your feet, a foot shower is sufficient. This also applies to dogs and other pets.
Can there be problems with the sand filter pump?In rare cases it can happen that sand gets into the water due to a damaged or overfilled sand filter system. In this case you will need to refill or repair the pump. The lamellae need to be changed most frequently, as they wear out quickly as a result of the filtering process. After that, the pool only needs to be refilled.
Can the wrong filter sand be used?Yes, wrong grit can be used. For this reason, check beforehand which grain size is required for your sand filter system. In most cases it is sufficient if you use the appropriate filter sand to prevent sand in the bathing water in the long term.